Feeds:
Posts
Comments

Posts Tagged ‘where are shuttles launched’

Launch Control Center, VAB and shuttle hangar -- Current header Photograph

Launch control at Kennedy Space Center has four firing rooms in a building adjacent to the Vehicle Assembly Building, and across the street from Press Complex 39.

Firing Room #4 is the most modern and is where the last 20 space shuttle missions were launched from. Just next door is Firing Room #3 which is very 1960s and retro. This is where some of the Apollo moon missions were launched from.

The Firing rooms all have an expansive window giving superb views of Launch Pads 39A and 39B where both the shuttles and the Apollo moon fights lifted off. The problem? If you’re working to get the shuttles off the launch pads, you’re looking at monitors, not out the window. After launch, however, if you have time, it’s a great view.
.

Launch Control Center where all major missions have been launched since the Apollo landings on the Moon. LCC is on the left, and the Vehicle Assembly Building is on the right. The set of windows on the furthest left on the LCC is Firing Room #4, the most modern firing room where all recent shuttle missions were launched from. The large second set of windows from the left (ignore the small square set of windows which are a small VIP viewing room) is Firing Room #3 where some of the Apollo missions were launched. Barely visible behind the LCC is one of the shuttle hangars which are called Orbiter Processing Facilities or OPFs. The picture is taken from the Crawlerway that leads to launch Pads 39A and 39B on the east virtually on the shore of the Atlantic Ocean. This photograph looks to the west.


.

Foyer of the Launch Control Center (LCC) stands in the middle of the LCC with two firing rooms on each side of the LCC on upper stories


.

Firing Room #3 is very 1960s and retro, almost Buck Rogers today. But it still is fully operational and should backup be needed during a launch, this room would be ready. Along the back wall are plaques for every mission launched from this room, including the date of the launch and of the landing.


.

When Firing Room #4 was modernized, this room was no longer the firing room of choice and was not used during the final twenty shuttle launches. During countdowns, the number of people in the Firing Rooms gradually increases until at launch there were about 300 people in the firing room. After launch, control of a mission is instantly handed to the Mission Control Center in Houston, Texas, and the number of people working here drops quickly.

.
.
.”petecrow/NASA” © 2011 by / Peter M. Crow and the Peter Michael Crow Trust and by Seine/Harbour® Productions, LLC, Studio City, California.

Advertisements

Read Full Post »

Looking at ceiling, up Tower A of the VAB. Note that the tower goes all the way up, but that an area is open between Tower A (left) and Tower B (lower portion of photograph). This is obviously not a great picture.

How the VAB is constructed. The Vehicle Assembly Buiding at Kennedy Space Center, Florida, is the largest building, in terms of volume, in the world.

The VAB was constructed in the mid-1960s to assemble the rockets and capsule in the Apollo program. The Apollo program landed men on the Moon six times between 1969 and 1972. It also served in the Skylab program and for the past 30 years has been the place where the shuttles have been mated with their rockets prior to being taken, as a single unit, to the launching pads.

The VAB, at 500 feet, is an iconic building of the American space program and is visible for miles. It is adjacent and mere steps from the Launch Control Center and its four firing rooms where the Apollo, Skylab and Shuttles have been launched. The VAB is also directly across the street from the Complex 39 Media Site where all media coverage of the launches of the shuttle originates. The VAB is adjacent to the three Orbiter Processing Facilities (OPF), the shuttle hangars. To the northwest of the VAB, several miles away, is the Shuttle Landing Facility (SLF), the runway where shuttles land in Florida. Shuttles also land in California and New Mexico when weather conditions do not permit a Florida landing.

The VAB is constructed of six supporting towers designated A, B, C, D, E and F. Three of these towers each inter-connect up to the 16th floor on opposite sides of the main open bay. The bays between the towers are open above the 16th floor.

The shuttle bays themselves are in between the D and E, and the E and F towers. Therefore, to place a shuttle in one of the shuttle bays, a shuttle must first be lifted from the main central bay, above the 16th floor, and then moved laterally into the shuttle bay, before being lowered and secured to the five-story high Crawler which will carry the shuttle to the launching pad.

Floor plan of the Vehicle Assembly Building. On May 18, 2011, the shuttle Atlantis was moved from the Transfer Aisle into High Bay 1 between Towers D and E.

. . . . . . . . . . . . . . .
.
.
.”petecrow/NASA” © 2011 by / Peter M. Crow and the Peter Michael Crow Trust and by Seine/Harbour® Productions, LLC, Studio City, California.

Read Full Post »